Base structure:

I-BEAM –IPE- 150

Door:

0.60mm pre painted galvanized steel sheet
  Floor structure:
  • SHS 80 x 40 ,rust protected

  • 18mm wbp plywood

  • 0.60mm galvanized steel sheet

Tensile Strength

240Mpa

Galvanizing

IS:277/JIS: 3302

  • 2mm thick antistatic floor tiles

 

Substrate

IS: 513 Cold Rolled Steel Coils

Tensile Strength

240Mpa

Galvanizing

IS:277/JIS: 3302

Zinc Coating

Pure Lead Free Zinc 120 GSM (both side mass)

Pre-Painting

IS: 14246/ JIS: 3312

Type of Coating

RMP/SMP

Top coating

5 um primer, 25 um polyester

Back coating

5 um epoxy

  • 100mm x 100mm x 3mm thick galvanized steel sheet inside the door for hinge fixing

  • Heavy duty S.S hinges, lock and rubber gasket

  • Extruded aluminum sections for frame and lip, designed and manufactured for MCIC - Alloy 6063 (BS EN : 755 – 9 – 2001)

  • Monobolt structural rivets

  • Ultra-grip high strength

Tensile Strength

2150lbs

Shear Strength

2500lbs

Wall / Roof / External roof panel:  0.60mm pre painted galvanized steel sheet  
   

Substrate

IS: 513 Cold Rolled Steel Coils

Tensile Strength

240Mpa

Galvanizing

IS:277/JIS: 3302

Zinc Coating

Pure Lead Free Zinc 120 GSM (both side mass)

Pre-Painting

IS: 14246/ JIS: 3312

Type of Coating

RMP/SMP

Top coating

5 um primer, 25 um polyester

Back coating

5 um epoxy

 
    18mm commercial plywood (Internal reinforcement for equipment fixing)

Outer Angles:

Extruded aluminum section 75x75 x 4mm(other sizes available)
    SHS 80x 20mm , rust protected   Alloy 6063 (BS EN : 755 – 9 – 2001)
         
  Polyurethane Foam (Bayer, Germany)    
 
Physical Properties Unit Average Measured Value Physical Properties

Density Of Foam

KG/M3

42 ±5%

DIN 53 420

Thermal Conductivity

BTU/I2/F/°INCH

13 ±2%

ASTMC 177

Thermal Conductivity

W/KM

0.022

DIN 52612

Closed Cells

%

94

ISO DP 2246

Compressive Strength

KG/CM2

 2.1

ASTM D 1621

Compressive Strength

N/MM2

0.20

DIN 53 421

Compression

%

10

DIN 53 421

Flexural Strength

N/MM2

0.30

DIN 53 432

Bending

MM

10

DIN 53 423

Fire strength/DIN

-

-

DIN 4105 B3

Extent of Burn

-

Self Extinguishing

BS-4735

Dimensional Stability C

%

10

Length & Width Tested at -180° C to 100° C for 48 hr. at 90% , Relative humidity

At - 25° C

%

0.1%

-

At + 38° C

%

0.1%

-

At + 90° C

%

0.4%

-

Temperature Range

 °C

 -180° C To 100° C

-

Water Absorption

%

2%

At Max 98% RH

Water Vapour Permeability

ng/PASM

5.5

S-11239

         
  Waterproofing System  
 

Silpruf, GE Bayer silicones is a one-part, neutral, low modulus silicone sealant, which cures with atmospheric moisture to form a highly elastic rubber seal for building joints and glazing applications. Its is unaffected by weathering conditions such as sunlight, uv-radiation, rain, snow and temperature extremes. The excellent weatherability and its high movement accommodation enables the sealant to perform even after many years of exposure.
 

As cured

Value

Test method

Ultimate tensile strength

1.6 mpa

ASTM D412

Ultimate elongation, %

700

ASTM D412

Tensile at 100 % elongation

0.4 mpa

ASTM D412

Ultimate elongation, %

300

ISO 8339

Peel strength, @ 21 deg.

7 KN/M

ASTM C794

Elastic recovery

90 %

DIN 52458

Service temp. range(after cure)

- 50 to 100 deg.c

 

         
  Hot Dip Galvanizing    
 
  • Minimum average zinc coating as per BS 729/ EN ISO 1461 : 1999 & ASTM A- 123

  • Vent holes are drilled as per ASTM A 385

  Note: Design and specification are subject to change without prior notice for product continuous development

Main Material Specification

Main material or components used in the construction are identified and listed as follows:

 

 

Home  |  About Us  |  Products  |  Gallery  |  Dealer Locator  |  Contact Us

Copyright © 2009 www.mci-oman.com. Designed by eDesigners